MDD01M-05
Stock number: C009580
Manufacturer: MEANWELL
€4.41 incl. VAT €3.64 Excl. VAT
Product description
The MEAN WELL MDD01M-05 is a miniature isolated DC/DC converter from the MDD01 series, designed for medical electronics, measurement instruments, analogue circuits and galvanically isolated power systems. From a nominal 12 V DC input, it generates two symmetrical outputs of +5 V DC and −5 V DC with a common COM reference point. Each output provides up to 100 mA, with a combined rated output power of 1 W. Its compact SIP7 package and through-hole PCB mounting allow straightforward integration into electronic equipment requiring bipolar power rails and high isolation strength.
A key advantage of the MDD01M-05 is its galvanic isolation between input and output, with a withstand voltage of 6,000 V DC / 4,200 V AC. This enables separation of power domains and helps reduce unwanted potential differences between sections of an electronic system. The converter is designed for applications with enhanced medical electrical safety requirements and features reinforced insulation. The manufacturer specifies an isolation level of 1× MOPP / 2× MOOP under defined conditions. Its low typical 5 pF isolation capacitance is particularly beneficial in sensitive analogue and measurement circuits. The symmetrical ±5 V supply is suitable for operational amplifiers, instrumentation amplifiers, signal conditioning circuits and analogue interfaces requiring both positive and negative supply rails.
The MEAN WELL MDD01M-05 operates from a 10.8–13.2 V DC input, corresponding to ±10% of its nominal 12 V rating. It achieves a typical efficiency of 78% and operates at a switching frequency of approximately 100 kHz. Its outputs are unregulated, meaning that the actual output voltages depend on input voltage and the load on each rail. The manufacturer specifies ±5% output voltage accuracy, ±10% load regulation and maximum ripple and noise of 75 mVp-p under defined test conditions. The recommended load range for each output is 10–100 mA, with a maximum capacitive load of 470 µF per output. A typical 14 mA no-load input current and 105 mA full-load input current support accurate sizing of the primary power supply circuit.
The converter uses natural convection cooling and supports an operating temperature range of −40 to +85°C, subject to derating. Its integrated short-circuit protection is designed for temporary fault conditions lasting up to 3 seconds, and the manufacturer recommends a 200 mA slow-blow input fuse. The module is supplied in a compact SIP7 plastic package measuring 19.5 × 9.8 × 12.5 mm, with an approximate weight of 4.2 g. Electrical connections are made through through-hole PCB solder pins, with +Vout, COM and −Vout providing a convenient symmetrical supply arrangement. Combining 1 W output power, dual ±5 V rails, 12 V input, 6 kV DC isolation and 78% efficiency, the MDD01M-05 is a suitable solution for sensitive analogue circuits, medical electronics and low-power galvanically isolated systems.
Key features
-
Product type: isolated PCB-mount DC/DC converter
-
Manufacturer series: MDD01
-
Construction: encapsulated SIP7 module
-
Number of outputs: 2, symmetrical
-
Nominal input voltage: 12 V DC
-
Input voltage range: 10.8–13.2 V DC
-
Input voltage tolerance: ±10%
-
Output voltage 1: +5 V DC
-
Output voltage 2: −5 V DC
-
Symmetrical output voltage: ±5 V DC
-
Rated output current 1: 100 mA
-
Rated output current 2: 100 mA
-
Load range per output: 10–100 mA
-
Combined rated output power: 1 W
-
Output regulation: unregulated converter
-
Typical efficiency: 78%
-
Switching frequency: approximately 100 kHz
-
Output voltage accuracy: ±5%
-
Ripple and noise: 75 mVp-p maximum
-
Load regulation: ±10%
-
Maximum capacitive load: 470 µF per output
-
Typical no-load input current: 14 mA
-
Typical full-load input current: 105 mA
-
Input filter: internal capacitor
-
Galvanic isolation: yes
-
Input-to-output withstand voltage: 6,000 V DC / 4,200 V AC
-
Isolation resistance: 100 MΩ at 500 V DC
-
Typical isolation capacitance: 5 pF
-
Insulation type: reinforced
-
Isolation level: 1× MOPP / 2× MOOP under manufacturer-specified conditions
-
Protection functions: short-circuit protection
-
Maximum short-circuit duration: 3 seconds
-
Recommended input fuse: 200 mA slow-blow
-
Cooling method: natural convection
-
Operating temperature: −40 to +85°C, subject to derating
-
Operating humidity: 20–90% RH, non-condensing
-
Storage temperature: −55 to +125°C
-
Vibration resistance: 2G
-
Mounting type: through-hole (THT)
-
Package: SIP7
-
Number of populated pins: 5
-
Pin configuration: 1 +Vin, 2 −Vin, 5 −Vout, 6 COM, 7 +Vout
-
Dimensions: 19.5 × 9.8 × 12.5 mm
-
Approximate weight: 4.2 g
Target applications
-
Medical electronics and diagnostic instruments
-
Galvanically isolated analogue power supplies
-
Operational amplifiers requiring symmetrical ±5 V rails
-
Instrumentation amplifiers and measurement systems
-
Analogue filters and signal conditioning circuits
-
Isolated communication and data interfaces
-
Sensitive sensors and sensor modules
-
Laboratory and test electronics
-
Embedded electronic systems with a 12 V DC supply
-
OEM manufacturing of medical and measurement equipment
Parameters
Product parameters
| Description: | DC/DC converter unregulated |
| Case: | SIP-7 |
| Operating temperature: | -40~85 °C |
| Dimensions: | 19,5x9,8x12,5 mm |
| Output voltage DC: | -5 V |
| Output current: | ±100 mA |
| Series: | MDD |
| DC input voltage: | 10,8~13,2 V |
| Power of convertor: | 1 W |
| Number of outputs: | 2 |
| Isolation: | 6000 V |
| Weight: | 4,2 g |
| Efficiency (typ.): | 78 % |
| Model series: | MDD01 |
| Approval agency: | CE, cURus |
| Protection: | Short Circuit Protection (SCP) |
Packaging and legislation
| Typ balení: | Tube |
| Původ: | TW |
| Small packing quantity: | 25 |
| Large packing quantity: | 3000 |
| Customs nomenclature: | 85044095 |
Files for download
| MDD01.pdf |
PDF, 84.24 kB |